Atlas Gas Geyser Repair in Alberton

Kurts Gas Installers repairs Atlas gas geysers in Alberton and across the East Rand. Over 15 years and more than 1,000 installations, and every repair starts with a proper diagnosis and a quote before we touch anything. Call 083 592 5450.

Book a Repair
Gas geyser burner and gas valve opened up during a service

Gas geyser not working?

What We Repair

We repair gas geysers that will not ignite, units that light and then cut out, geysers with no hot water or water that is not hot enough, leaks, error codes, noisy or blocked burners, tired thermocouples, perished flex connectors and faulty regulators. We also service the unit as part of the callout, and we work on residential and commercial geysers. We work on the gas side of the installation, test the pressure and check for leaks before we leave.

We repair the water side of the geyser as well as the gas side: heat exchangers, leaks inside the unit, blocked filters and plumbing restrictions at the connections. We assess the fault and quote before we start, and every replaced part carries a 1-month warranty. If the gas installation is not compliant, we will quote to bring it up to standard.

15

Years Experience

1000+

Gas Installations Completed

Rinnai gas geyser with copper pipework on a brick wall

Atlas gas geyser not igniting? Start with these checks

If the geyser ticks but does not light, check the gas bottle first. A bottle that feels light, or a shut-off valve that was closed, is the most common cause. After a refill there can be air in the line; cycling the hot tap on and off can clear it, but bleeding the line is a job for a registered installer.

Battery units: replace the batteries. Fan-forced units: check the 220 V supply and the controller. If the unit shows an error code, check the manual. If none of that fixes it, the fault is in the gas valve, the ignition circuit or the pressure, and it needs a manometer and a registered installer. Our guide to fixing a gas geyser walks through the checks in more detail.

Symptom What we check
Ticking but not igniting Gas supply, shut-off valve, air in the line, batteries or power, gas pressure
Lights then cuts out Flame rectification, burner condition, earth wire, thermocouple, gas pressure
No hot water / lukewarm Pipe sizing, regulator capacity, flow rate, filter, gas pressure
Leaking Heat exchanger, pipework, fittings, gas leak at the connections
Huge flames or soot Regulator, gas valve, burner and heat exchanger

The table is a guide, not a diagnosis. The same symptom can have more than one cause, and the only way to know which part has failed is to test the unit and the gas pressure on site.

It lights and then cuts out

A geyser that lights and then shuts off is usually not sensing the flame. The controller sends a small current through the flame and expects it back; a dirty burner, a broken earth wire or a tired thermocouple breaks that signal, so the controller closes the gas valve to be safe.

This is not a DIY fix. We clean the burner, check the flame rectification path and test the gas pressure. If the unit has been cutting out for a while, the repeated ignition cycles can also leave the burner and heat exchanger sooted up, which makes the next fault worse.

No hot water, or the water is not hot enough

If the unit lights but the water stays lukewarm, the gas line may be undersized, the regulator may be failing, or the flow may be too high for the unit. We test the pressure at the unit and check the pipe sizing against the geyser's data sheet.

A blocked filter or a plumbing restriction can also reduce the flow enough to stop the unit from firing. If the flame is weak or the water temperature moves around, stop adjusting the unit and have the gas side tested - a gas valve running at the wrong pressure can be damaged.

The geyser is leaking

A water leak from the heat exchanger can often be fixed by replacing it; a leak from the pipework or a fitting may just need tightening. If you smell gas, turn the cylinder off, open the windows (if the unit is indoors or enclosed), do not switch anything on, and call us.

We will tell you whether a repair or a replacement makes more sense before we start. We do not patch a leaking heat exchanger - we replace it - but on an old unit the cost of the part may not be worth it.

Repair or replace?

A thermocouple, a regulator, a flex connector or a gas valve is usually worth repairing. A heat exchanger can be replaced, but on an old unit the cost of the part may not be worth it; we will tell you.

If a replacement makes more sense, we install geysers from 6 to 26 litres per minute. See gas geyser installation for what the job involves and what it costs.

What happens on a repair callout

We diagnose the fault, quote before we start, and repair what can be repaired. Most repairs take between 30 minutes and 3 hours, depending on the fault. We test the pressure and check for leaks, and we leave the unit working. We work Monday to Friday, 8am to 5pm. If a technician is free we will normally get to you the same day, and if we cannot, we will say so on the phone.

A replaced part carries a 1-month warranty. A new installation carries a 1-year workmanship warranty.

What affects the repair price

Every repair starts with a diagnosis. The price depends on the fault and the part - a thermocouple is not a heat exchanger - and we only replace what needs replacing. We cannot give a quote or estimate over the phone because the geyser has to be assessed first; once we have diagnosed the fault, we quote before we start.

Every replaced part carries a 1-month warranty. The callout price is in the FAQ below.

Atlas and the other brands we repair

We work on Atlas gas geysers, and on Paloma, Rinnai, Bosch, Dewhot, Delta and Alva. Most parts are interchangeable between these brands, but there are cases where a manufacturer no longer sells the replacement part; we will tell you if that is the case. We do not claim to be an authorised service agent for any manufacturer, so if the unit is still under warranty, check with the importer first.

Areas around Alberton that we service

We cover Alberton and the neighbouring East Rand suburbs: New Redruth, Randhart, Brackenhurst, Bedfordview, Edenvale, Boksburg, Brakpan and Kempton Park. The same repair service has a page of its own for Bedfordview, Edenvale, New Redruth and Boksburg.

For the whole repair service, including the faults we cover, see gas geyser repair. If you are outside these areas, call us and we will tell you straight away whether we can take the job on.

Two LPG cylinders in a secure cage for a gas reticulation system
Gas cylinder connected outside with a regulator and pipework

Why Alberton calls us for geyser repairs

Diagnose first

We find the fault and quote before we start. No guessing and no replacing parts until we know which one has failed.

Registered

The gas work is done by a registered installer, pressure tested and leak tested, and the unit is left working before we leave.

Honest advice

We will tell you when a repair is worth it and when a replacement makes more sense. We do not replace a unit that can be repaired.

Local

We work out of Elspark in Germiston and cover Alberton, Monday to Friday, 8am to 5pm, with a 1-month warranty on replaced parts.

Frequently asked questions about gas geyser repairs

Why is my Atlas gas geyser not igniting?

My gas geyser sparks but does not ignite. What does that mean?

Why does my gas geyser ignite and then shut off?

Why is my gas geyser leaking water?

Why is my hot water not hot enough?

Can I repair my gas geyser myself?

Do you repair Atlas, Paloma, Rinnai, Bosch, Dewhot, Delta and Alva geysers?

What warranty do you give on a repair?

How much does a gas geyser repair cost?

How long does a repair take?

Do you service geysers, or only repair them?

Do you work on commercial geysers?

Do you come out to Alberton?

Can you give me a quote or estimate over the phone?

Start with the gas supply: a bottle that is nearly empty, a shut-off valve that was closed, or air in the line after a refill. Battery units need good batteries and fan-forced units need 220 V. If the unit still ticks but does not light, the gas pressure or the ignition circuit needs testing by a registered installer.

The ignition circuit is working, but the gas is not reaching the burner or the controller is not sensing a flame. Common causes are a closed valve, an empty bottle, air in the line, a faulty regulator or a dirty burner. Do not keep cycling the unit if you smell gas - turn the cylinder off and call us.

The controller is not receiving the flame signal, so it closes the gas valve to be safe. A dirty burner, a broken earth wire or a tired thermocouple will do it. We clean the burner and test the flame rectification path and the gas pressure.

A leak from the heat exchanger can often be fixed by replacing the heat exchanger; a leak from the pipework or a fitting may just need tightening. We will tell you whether a repair or a replacement makes more sense before we start. If you smell gas as well, turn the cylinder off, open the windows (if the unit is indoors or enclosed) and call us immediately.

The gas line may be undersized, the regulator may be failing, or the flow may be too high for the unit. We test the pressure at the unit and check the pipe sizing against the geyser's data sheet before we change any parts.

You can check the gas bottle, the shut-off valve, the batteries and the error code. Anything inside the gas side of the unit is work for a registered installer - gas work is regulated, and the wrong repair can leave the unit unsafe or damage the gas valve. Our how-to-fix guide explains what is safe to check.

Yes. We work on those brands. Most parts are interchangeable between them, but there are cases where a manufacturer no longer sells the replacement part; we will tell you if that is the case. We are not an authorised service agent for any manufacturer, so if the unit is under warranty, check with the importer first.

A replaced part carries a 1-month warranty. If something we replaced fails inside that month, we come back and put it right. A new installation carries a 1-year workmanship warranty.

Our callout is R950, depending on the area, and it includes a service of the geyser. Spares are charged separately. We cannot give a quote or estimate over the phone because the geyser has to be assessed first; once we have diagnosed the fault, we quote before we start.

Between 30 minutes and 3 hours, depending on the fault.

We service geysers as well. A service is included in the R950 callout; if we find a fault during the service, we quote the repair before we start. Spares are charged separately.

Yes. We work on residential and commercial gas geysers.

Yes. Alberton is part of our East Rand service area, along with New Redruth, Randhart, Brackenhurst, Bedfordview, Edenvale, Boksburg, Brakpan and Kempton Park. If you are outside that list, call us and we will tell you straight away whether we can take the job on.

No. We cannot quote or estimate over the phone because the geyser has to be assessed first. We diagnose the fault on site and quote before we start the repair.

Contact Us

Whatsapp Us

Click To Whatsapp